PEM Insertion

PEM Hardware Insertion Services

GSM installs PEM® self-clinching nuts, studs and standoffs in the sheet metal parts we laser cut, punch and stamp in-house, adding permanent, reusable threads to metal too thin to tap. It’s how dash panels, instrument clusters, electrical enclosures and circuit board mounts get their hardware, without loose nuts, welding or a second supplier.

Comprehensive Metal Manufacturing Solutions

We offer an extensive range of metal manufacturing capabilities, eliminating the need for multiple manufacturers.

Robust Supply Chain Support

We excel in providing enhanced supply chain stability and dedicated support for minimal disruptions.

Manage Large-Scale Projects

We offer a state-of-the-art facility equipped to tackle projects requiring large metal components.

Collaborative Engineering

Our expertise helps improve manufacturability and reduce costs.

Our PEM Insertion Equipment

GSM operator installing PEM self-clinching standoffs into a laser-cut aluminum panel on a Haeger insertion press
An operator presses PEM self-clinching standoffs into a laser-cut aluminum panel on GSM's Haeger insertion press.

PEM hardware is installed on a Haeger 824WT-3H insertion press in our South Bend, Indiana plant, the same building where we laser cut and stamp the panels. Haeger presses are built by PennEngineering, the company that makes PEM fasteners, specifically for installing self-clinching hardware. See the full equipment list.

MachineHaeger by PEM 824WT-3H nut insert press
LocationSouth Bend, IN
Capacity8 tons
Configuration1-axis press
AutomationManual load with vision system
Max. workpiece24″ (610 mm)
Hardware range#2-56 to 1/2″ (M2 to M12)
RateUp to 1,500 inserts per hour

Unlike a hammer or an arbor press, the Haeger applies a controlled, parallel squeezing force of up to 8 tons, with dedicated tooling for each fastener type and a vision system at the press. Every nut, stud and standoff seats square and flush, and the panel around it stays flat.

PEM Insertion for OEM Production

Sheet metal is often too thin to hold a tapped thread, and loose nuts, lock washers and cage nuts add parts, assembly time and the risk of hardware rattling loose inside a finished product. Self-clinching fasteners solve that. Once a PEM nut, stud or standoff is pressed into the panel, it becomes a permanent part of it: it won’t spin, push out or fall off, and the threads can be used again and again during service.

For OEMs, that means faster assembly on your line, since threads are already in the part and accessible from one side, and fewer loose parts to buy, count and stock. You receive one finished component per part number instead of a panel plus a bag of hardware.

Installed Flush, Square and Tight

A self-clinching fastener only performs if the hole is the right size, the panel is the right hardness and the fastener is pressed in fully. GSM controls all three. Holes are cut or pierced to the fastener’s specified size in the same program or die that makes the part, and hardware is kept in separate, labeled bins by part number at the press so the wrong nut can’t end up in the wrong hole.

Before a run is released, the first part is checked against your drawing: correct fastener in each location, fastener seated flush to the panel, and threads that accept the mating screw.

What Is PEM Insertion?

PEM insertion is the process of pressing self-clinching fasteners (threaded nuts, studs and standoffs) into a punched or laser-cut hole in sheet metal. “PEM” is the brand name of PennEngineering, which invented the self-clinching fastener, and engineers often use “PEM nuts,” “PEM studs” and “PEM inserts” for this kind of hardware, whatever the brand. You will also see them called clinch nuts, press nuts or press-in studs.

A self-clinching fastener is harder than the panel it goes into. As the press squeezes it into the hole, a displacer ring on the fastener pushes the surrounding sheet metal into an undercut groove in the fastener’s shank. That cold-flowed metal locks the fastener against push-out, and a knurled or serrated collar keeps it from turning under torque. No heat, welding or adhesive is involved, so the threads stay clean and the finish on the panel is not burned.

The PEM Insertion Process

Every self-clinching fastener GSM installs goes through the same five steps:

  1. Design review: We check the hardware series against your sheet thickness and material, and confirm edge distance, spacing and clearance to bend lines using the fastener manufacturer’s published data.
  2. Hole making: Mounting holes are laser cut, punched or pierced in the stamping die to the fastener’s specified hole size, so the fit is consistent from the first part to the last.
  3. Sequencing: Most hardware goes in while the blank is still flat, before press brake forming. Hardware close to a bend goes in after forming. We plan insertion around plating, paint and powder coat, and mask threads when coating comes after.
  4. Pressing: The fastener is placed in the hole and squeezed in with parallel force until its head or shoulder is flush with the panel.
  5. Inspection: Location, seating and thread fit are verified before parts move on to finishing, assembly or shipping.

Design Tips for Self-Clinching Hardware

  • Panel hardness: The panel must be softer than the fastener. Stainless steel panels need hardened fasteners made for stainless.
  • Install on the right side: Put nuts on the side that keeps the screw load pulling the fastener into the panel, not out of it.
  • Keep holes clean: Don’t countersink or chamfer self-clinching holes. The fastener needs the full hole wall to clinch.
  • Respect edge and bend distances: Fasteners placed too close to an edge or bend can bulge the panel or fail to hold.

The GSM Approach

Because GSM builds the stamping dies, runs the lasers and presses, and installs the hardware, the fastener is designed into the part from the start. Mounting holes are pierced in the die or cut in the same laser program as the part profile, so hole size and position don’t drift between suppliers. Our engineers will flag a fastener that’s too close to a bend or the wrong series for your material before tooling is built, not after the first parts fail.

Self-Clinching Nuts, Studs & Standoffs

GSM sources the PEM hardware, or an approved equivalent, for you and installs it from #2-56 to 1/2″ (M2 to M12) in steel, stainless steel and aluminum panels. You don’t need to buy or ship us fasteners.
  • Self-clinching nuts for load-bearing threads in thin sheet, including flush, floating and locking styles
  • Self-clinching studs for mounting brackets, components and ground connections, with threads that won’t strip like a tapped hole
  • Self-clinching standoffs, both through-hole and blind, for mounting and spacing printed circuit boards and panels
  • Hardware on stamped and laser-cut parts, from prototypes to production runs
  • Weld nuts and spot welding when a joint calls for a welded fastener instead
  • Assembly and kitting of finished panels into ready-to-install subassemblies

PEM Hardware for Dash Panels, Instrument Clusters and Circuit Boards

Self-clinching hardware is at its best where thin panels have to carry components. GSM installs it for:

  • Dash panels and operator consoles: studs and nuts that mount gauges, switches, displays and wiring harnesses in cabs for agricultural and construction equipment.
  • Instrument clusters: threaded mounting points on the sheet metal housings and brackets that hold instruments in place.
  • Circuit board mounting: standoffs that hold PCBs at a fixed height above a sheet metal chassis, keeping solder joints clear of the panel and giving a ground path where one is needed.
  • Electrical enclosures and covers: nuts and studs for doors, DIN rails, back panels and removable access covers.

In each case the fastener is installed before the panel reaches your line, so your assemblers drive a screw or start a nut and move on.

Why Manufacturers Choose GSM for PEM Insertion

OEMs choose GSM because hardware insertion isn’t a standalone service here. It’s one step in a connected manufacturing process that includes tool and die, metal stamping, laser cutting, bending, welding and assembly. Your panel is cut, formed, fitted with hardware and checked by the same team, under one purchase order, with one point of accountability.

That removes the shipping, handling and scheduling gaps you get when a part travels to a separate shop just to have nuts pressed in, and it means the people who made the hole are responsible for how the fastener fits in it.

104 Years of Protecting Your Brand™

For 104 years, GSM has kept its promises to the OEMs and manufacturers who depend on it. That kind of track record isn’t a marketing line — it’s what happens when a manufacturing partner survives multiple recessions, generations of ownership, and decades of shifting manufacturing trends without missing a delivery window. Longevity matters more than most sourcing teams give it credit for. Every time you qualify a new metal stamping supplier, you’re taking on risk: unproven tooling, unproven quality systems, unproven leadership. A supplier that has been running presses for over a century has already worked through the failure modes that take down younger shops — cash-flow gaps, key-person dependency, equipment obsolescence, quality drift. That stability is why GSM frames its work around Protecting Your Brand™. Your customers don’t see GSM’s dies, presses, or tooling room — they see your product, on time, to spec, every time. A missed shipment or a quality escape doesn’t just cost you a part. It costs you your reputation with your own customers. 104 years in business means GSM has already built the systems, redundancy, and institutional knowledge to keep that from happening to your brand — not because GSM is new, but because it’s proven.

PEM Insertion, Made in the USA

Every part GSM fits with PEM hardware is made in the USA, at our plant in South Bend, Indiana. Keeping laser cutting, stamping, hardware insertion and assembly together in the Midwest shortens supply chains, cuts freight between suppliers and gives you a partner you can visit, audit and call directly.

A Competitive Advantage

See how GSM tackles the toughest stamping and fabrication challenges in real time. Watch our team in action and see why leading OEMs trust us with their biggest projects.

Let's Build Something That Lasts

Need PEM nuts, studs or standoffs installed in your sheet metal parts? Send us your drawings with the hardware callouts, and we’ll quote the panel and the insertion together.

Frequently Asked Questions

Here’s what OEMs and engineers ask most often about PEM inserts and self-clinching hardware installation.
What is PEM insertion?

PEM insertion is the installation of self-clinching fasteners (nuts, studs and standoffs) into sheet metal using a press. The fastener is squeezed into a properly sized hole, and the panel metal cold-flows into a groove on the fastener, locking it in permanently. PEM® is a registered trademark of PennEngineering.

A PEM nut is a self-clinching nut that is pressed into a hole in sheet metal instead of being welded or held with a wrench. It gives thin panels strong, reusable threads that are accessible from one side and won’t spin or fall out during assembly or service.

A nut adds an internal thread to the panel for a screw. A stud adds a threaded post that sticks out of the panel, for mounting a component with a nut. A standoff is a threaded or unthreaded spacer that holds a circuit board or second panel at a set distance from the sheet metal.

Self-clinching hardware works in steel, stainless steel and aluminum sheet, as long as the panel is softer than the fastener. Each fastener has a minimum sheet thickness and a minimum distance from the hole to the edge, published by the manufacturer. We check both during quoting and recommend another fastener series if a part is too thin or a hole is too close to an edge.

Yes. That’s the most common way we do it. Mounting holes are pierced in the stamping die or cut in the laser program, GSM sources the hardware, and it’s pressed in before the part ships, so you receive a finished component on one purchase order.

Usually before. Inserting hardware while the blank is flat is faster and keeps the press tooling square to the panel. Fasteners close to a bend line, or where the formed shape would block the press, are installed after bending.

Yes. GSM supports prototypes and short runs, so you can confirm hardware placement and fit before scaling up to production volumes.

GSM accepts STEP, IGES, SolidWorks, Pro/E (Creo), AutoCAD (DWG/DXF) and PDF technical drawings. Please include the hardware part numbers or callouts on the drawing.

GSM installs self-clinching hardware in dash panels, consoles and cab components for agricultural equipment and construction equipment manufacturers, and in brackets, covers and enclosures for industrial and electrical products.

Yes, and on many parts that’s the preferred order, because the threads stay free of coating. Hardware can also go in before finishing when the threads are masked. We set the sequence for each part based on the finish, the fastener and how the part will be assembled.

See Other Capabilities

Welding
Warehousing
Leveling

Get a Quote for Your Next Project

Let our expertise work for you. Contact us today to discuss your metal fabrication needs and receive a competitive quote.

General Stamping & Metalworks, Inc.
South Bend Location
25101 Old Cleveland Rd
South Bend, IN 46628
574-288-0611
info@gsmwinc.com
General Stamping & Metalworks, Inc.
Tomah Location
328 Cardinal Ave
Tomah, WI 54660
608-374-4769
info@gsmwinc.com